Table Saw Jigs Worth Buying in 2026
Watching on TV? See all tool links from this video
These are the table saw jigs I would add to my saw right now. The list starts with a digital thin rip jig and a digital miter gauge that reads down to a twentieth of a degree. Here is what each one does well and where each one falls short.
The Short Answer
- The best table saw jig on this list is the iGaging Digital Thin Rip Jig. I gave it a 10 out of 10.
- The iGaging Digital Miter Gauge is the first miter gauge I have found accurate to a twentieth of a degree.
- The Rockler Crosscut Sled is the best table saw sled I have ever used, and I bought it with my own money.
- The new GRR-RIPPER Air adds more grip and a tunnel that lets the blade pass through the center leg.
- For a jobsite saw fence upgrade, look at TSO. For bigger saws, look at the Bow Xtender Fence and L Fence.
The Best Table Saw Jigs Worth Buying in 2026
Out of every table saw jig in this lineup, the iGaging Digital Thin Rip Jig is my favorite. Thin rip jigs are one of the most popular tools I have ever featured. This is the first one I have seen with a digital gauge on it.
The digital miter gauge and the Rockler sled also earned a 10 out of 10 from me. The GRR-RIPPER Air and the fence upgrades round out the list for anyone who wants safer, more accurate cuts.
| Jig | What It Does | Standout Feature | My Rating |
|---|---|---|---|
| iGaging Digital Thin Rip Jig | Sets repeatable thin strip widths | Digital readout in inches, fractions, or metric | 10/10 |
| iGaging Digital Miter Gauge | Crosscuts and angle cuts | Accurate to a twentieth of a degree | 10/10 |
| Rockler Crosscut Sled | Crosscuts and angles from 0 to 50° | Micro adjust stop block and built-in clamp | 10/10 |
| Microjig GRR-RIPPER Air | Pushes stock safely past the blade | X Air Heel and Safe Rip Tunnel | Not rated |
| Bow Xtender Fence and L Fence | Adds support and clamping pressure | Pattern cutting and edge jointing | Not rated |
iGaging Digital Thin Rip Jig: How It Works
A digital gauge lets you dial in the exact thickness you want for thin strips. It fits almost any table saw with a 3/4 inch miter slot, and a twist knob locks it in place.
Lock it in front of the blade, not beside it. Set right at the blade, your piece could jam between the blade and the jig.
There is no assembly. Pull the tab to unlock the installed battery, and a spare battery comes in the box. The display reads inches, fractions, or metric, with zero, power, hold, and ABS buttons for an absolute zero.
It glides butter smooth, and the screen updates in real time as you move it. To set a 1/4 inch strip, push the jig until it touches a tooth of the blade and set zero there.
Use the tooth, not the body of the blade, so you account for the tooth set. Then slide it out to 0.250, move it ahead of the blade, and lock it down.
From there, bump your fence over to the rolling bearing on the end and rip. My strips came out at a perfect 1/4 inch every time. You can pull the jig off and put it back later, and it still reads your setting.
See the iGaging Digital Thin Rip Jig at TayTools Affiliate link. We may earn a commission at no extra cost to you.
Watch the Full Test
The video shows each jig making real cuts, including the miter gauge readout moving under side pressure. That is easier to judge on screen than in text.
iGaging Digital Miter Gauge Review: Accurate to a Twentieth of a Degree
This is the first miter gauge I have found that gets accuracy down to a twentieth of a degree. I gave it a 10 out of 10. My 90° cuts and 45° cuts both came out dead accurate.
Setup and Miter Slot Fit
The handle goes on with a nylon washer under the gauge, a second nylon washer on top, then the metal ring. It screws in and is spring loaded.
It runs on a standard CR2032 battery behind a tiny screw. A mini screwdriver comes in the box, and the gauge turns itself off to save battery.
The miter bar adjustment is something I have never seen on a miter gauge. Four adjustment points run down the bar, and an Allen key moves each one in or out.
Each point has a spring loaded ball bearing that keeps tension against the slot. That keeps it gliding without wiggle, so your cuts stay accurate. A washer underneath also turns to catch a T shaped miter slot.
How to Zero a Digital Miter Gauge
Adjust the bar until it is snug with no wiggle. Then square the fence to the blade and lock the knob down.
1-2-3 set up blocks are a quick and dirty way to get close. They are cheap and easy, but not the most accurate.
See 123 Set Up Blocks at Amazon Affiliate link. We may earn a commission at no extra cost to you.
I prefer a bigger square. My Woodpeckers square is the one I trust for dead accurate setups. Use whatever square you trust.
See the Woodpeckers 1282 Square at Amazon Affiliate link. We may earn a commission at no extra cost to you.
Once it is square, hit the zero button. Now you can swing to 45° or 22.5°, and it returns to dead square every time you come back to zero.
The Fence and Flip Stop
The fence attaches with the included T bolts. The flip stop took me a minute. The black twist knob goes on top, and the lock nut goes through the side.
Snug the bolt just enough that the stop stays up when you flip it up. It slides where you need it and flips down for repeat cuts.
The sacrificial fence is plywood, while almost everybody else uses MDF. The bottom has a glide material that helps it slide and protects your saw top. The stick-on tape measure is included, but I have never found those very useful.
One Thing to Watch on the iGaging Miter Gauge
If you put heavy pressure on the left side during a cut, the readout can shift a little, even locked down. It typically comes back to square.
I have not noticed any inaccuracy in my cuts from it. Just know you may see that number move.
You can buy the gauge with or without the fence. If you have the budget, I recommend getting the fence.
See the iGaging Digital Miter Gauge with Fence at TayTools Affiliate link. We may earn a commission at no extra cost to you.
See the iGaging Digital Miter Gauge without Fence at TayTools Affiliate link. We may earn a commission at no extra cost to you.
GRR-RIPPER Air Review: What Changed on the New MicroJig
The GRR-RIPPER has been around for 25 years, and the Air version is a big upgrade. The bottom is redesigned with a grippier material.
The new X Air Heel adds an air pocket in the heel that grabs the back of the board as you push. That makes it a lot more stable through the cut.
MicroJig also added the Safe Rip Tunnel. The center leg now has a tunnel, so the blade can pass through it when you center it right.
The sight window on top and the drop-down support for thicker stock are still there. If you do not own a GRR-RIPPER yet, this is a fantastic one to start with.
GRR-RIPPER 100AIR vs 200AIR vs 300AIR
Most people should get the 100AIR, which is the basic GRR-RIPPER. The 200AIR adds some accessories, and the 300AIR includes all of them. You cannot go wrong with any of the three.
See the Microjig GRR-RIPPER 100AIR at TayTools Affiliate link. We may earn a commission at no extra cost to you.
See the Microjig GRR-RIPPER 200AIR at TayTools Affiliate link. We may earn a commission at no extra cost to you.
See the Microjig GRR-RIPPER 300AIR at TayTools Affiliate link. We may earn a commission at no extra cost to you.
Best Table Saw Crosscut Sled: Rockler Crosscut Sled
This is the best table saw sled I have ever used. I bought it with my own money and have not regretted a penny. It sold out for months after I first featured it.
The phenolic top is a hard formed material with some weight to it, which is a good thing. The fence is one of the best I have used on any crosscut sled, including the one I built.
The stop block has micro adjustments to dial in your cut and flips up out of the way. Angle settings run from 0 to 50°, and they are easy to read.
The fence extends for extra support, with a ledge that holds the extended piece. It also has a solid built-in clamp. A replaceable zero clearance insert comes in the package, so you can keep one for 90° and one for bevels.
I also bought the drop off platform, which keeps offcuts from falling and has its own stop block. A hole pattern on top lets you relocate the miter bar underneath. You can find more savings on my current Rockler deals page.
See the Rockler Crosscut Sled at Rockler Affiliate link. We may earn a commission at no extra cost to you.
See the Rockler Drop Off Platform at Rockler Affiliate link. We may earn a commission at no extra cost to you.
See the Rockler Crosscut Sled at Amazon Affiliate link. We may earn a commission at no extra cost to you.
See the Rockler Drop Off Platform at Amazon Affiliate link. We may earn a commission at no extra cost to you.
Will the Rockler Sled Fit a Jobsite Table Saw?
Rockler says it is not really made for jobsite saws. It will not work well on the SKIL saw I covered in my SKIL 10 inch table saw review, or on 8 1/4 inch saws. The tables are just too small.
On the DeWalt 10 inch jobsite saw, it actually worked fairly well. If your shop is tight on space, my post on the best table saw alternative for a small shop is worth a look too.
Table Saw Fence Upgrades: TSO and the Bow Xtender L Fence
TSO makes fence upgrades for SKIL, DeWalt, and a couple of other jobsite saws. They replace your rip fence so you can add accessories like featherboards. For what you get, they are quite inexpensive.
See the TSO Fence Upgrade at TSO Products Affiliate link. We may earn a commission at no extra cost to you.
If you would rather keep your fence or have a bigger saw, check out the Bow Xtender Fence. It comes in 24, 36, and 46 inch sizes, and I like the bigger size for most cases.
The bundle adds infeed and outfeed support, plus vertical clamping pressure. Bow also released the L Fence this year.
The L Fence can stand in for a router table in some situations. It handles pattern cutting and edge jointing, and it works on a band saw with the extended fence.
See the Bow Xtender Fence Bundle at TayTools Affiliate link. We may earn a commission at no extra cost to you.
See the Bow L Fence at TayTools Affiliate link. We may earn a commission at no extra cost to you.
All Tools From This Video
TayTools
- Shop All Deals at TayTools
- iGaging Digital Miter Gauge with Fence
- iGaging Digital Miter Gauge without Fence
- iGaging Digital Thin Rip Jig
- Microjig GRR-RIPPER 100AIR
- Microjig GRR-RIPPER 200AIR
- Microjig GRR-RIPPER 300AIR
- MicroJig Air Ultra 25th Anniversary Limited Edition (only 1,500 made)
- Bow Xtender Fence Bundle
- Bow L Fence
Rockler
Amazon
- Rockler Cross Cut Sled
- Rockler Drop Off Platform
- Woodpeckers 1282 Square
- 123 Set Up Blocks
- Fastcap Lefty/Righty Tape Measure
- Magnetic Workbench Tray
TSO Products
Affiliate links. We may earn a commission at no extra cost to you.Want deals like these sent to you every day.
Join The Morning Cut. Free daily tool deal email from Matt.
Browse all current tool deals at 731woodworks.com.
See all tool reviews. Every post from the 731 Woodworks blog.
Frequently Asked Questions
What is the best table saw jig to buy?
My favorite right now is the iGaging Digital Thin Rip Jig. Its digital readout sets exact strip widths, and my 1/4 inch strips came out perfect every time. It also holds its setting when you remove it and put it back.
How accurate is the iGaging digital miter gauge?
It reads down to a twentieth of a degree. My 90° and 45° cuts were dead accurate. Heavy pressure on the left side can move the readout slightly, but it returns to square.
What is a thin rip jig used for on a table saw?
A thin rip jig lets you rip repeatable thin strips with the offcut falling away from the fence side. You set the jig ahead of the blade and bump your fence against it for each cut. That keeps every strip the same thickness.
What is the difference between the GRR-RIPPER 100AIR, 200AIR, and 300AIR?
They share the same updated push block with the X Air Heel and Safe Rip Tunnel. The 200AIR adds some accessories, and the 300AIR includes all of them. For most people, the 100AIR is the one to get.
Does the Rockler crosscut sled fit a jobsite table saw?
It is not really made for jobsite saws. It will not work well on the SKIL table saw or 8 1/4 inch saws because the tables are too small. On the DeWalt 10 inch jobsite saw, it worked fairly well for me.
Does the iGaging digital miter gauge fit any miter slot?
It should fit any standard miter slot. Four adjustment points on the bar let you dial in the fit with an Allen key. A washer underneath turns to hold it in a T shaped slot.
Some links in this post are affiliate links. 731 Woodworks may earn a small commission at no extra cost to you.
These are the table saw jigs I would add to my saw right now, led by a digital thin rip jig that sets perfect strips every time. Plus a miter gauge accurate to a twentieth of a degree and the new GRR-RIPPER Air.