New Kreg Track Saw 2026: Universal Track, Routers and More
Kreg dropped a big lineup of new tools on September 15, 2026. There are new track saws, a new universal track, four new routers, a cordless Kreg Edge, and a handful of accessories. If you're shopping or doing your homework before you buy, this post breaks down every tool so you can see what's new and what fits your shop.
The biggest story is the track. Kreg moved to a universal track design, and that changes how these saws fit into a shop that already runs other brands.
Shop the new Kreg tools
Shop all the new Kreg tools Affiliate link. I may earn a commission at no extra cost to you.Prices valid at the time of this post but could change at any time. Check links for current pricing.
- Track saws
- Tracks and squares
- Routers
- Router accessories
- Joinery
- Cordless saws
- Charger and sanding
- Which to buy
- FAQ
Track saws and tracks
- Cordless Master Kit ACSCT3000B $1,106
- Cordless Saw + Track Kit ACSCT2000B $508
- Corded Saw + Track Kit ACSCT2000 $458
- Corded Track Saw Only ACSSAWUNIV $349
- Accu-Cut ACS2700 $99
- Universal Track 62" ACSCT62 $109
- Universal Track 26 1/2" ACSCT26 $49
- 90 and 45 Track Saw Square ACS4590 $49
Joinery
Routers and router accessories
- 20V 2 1/4 HP Plunge Router KPTBPR225B $299
- Corded 2 1/4 HP Plunge Router PRSPR225 $299
- 3 1/4 HP SureSpeed Router PRSPR325 $399
- 3 1/4 HP SureSpeed Motor PRSPR325M $349
- 1 1/4 HP Trim Router PRSPR125 $119
- Trim Router Plunge Base PRSTRPB $41.99
- Dock and Go Trim Router Table Top KRTRT100 $99
- Router Table Insert Plate PRS4040 $62.99
- SureCut 5 Piece Router Bit Set PRS4325 $34.99
Cordless saws, charger and sanding
What changed: the new Kreg universal track
Every new Kreg track saw and track in this launch uses a universal track design. That's the headline for anybody who already owns track gear from another brand.
Old Kreg track
- Proprietary track profile
- Only worked with Kreg saws
- Hard to mix into a shop with other brands
New Kreg Universal Track
- Same track design used by Festool, Makita, Milwaukee and others
- Anti tip slot that locks the new Kreg saws to the track
- Anti chip strip, GripMaxx grip strips, and glide strips
- Tracks connect for longer rip cuts
The anti tip tab is new on the Kreg track saws too. It rides in a slot on the Universal Track so the saw stays put when the weight shifts during a bevel cut.
New Kreg track saws: Adaptive Cutting System lineup
Kreg's track saws live under the Adaptive Cutting System name. You can go cordless or corded, buy a full kit, or start with the Accu-Cut sled and your own circular saw. Here's how the options line up.
| Kit | Price | Power | Blade | Track | Also included |
|---|---|---|---|---|---|
| Master Kit ACSCT3000B | $1,106 | 20V brushless | Not listed | 62" Universal | Project Table, 4.0 Ah battery, charger |
| Saw + Track Kit ACSCT2000B | $508 | 20V brushless | 40T thin kerf | 62" Universal | None listed |
| Saw + Track Kit ACSCT2000 | $458 | 12 amp, 120V | 48T | 62" Universal | None listed |
| Track Saw ACSSAWUNIV | $349 | 12 amp, 120V | 48T | Not included | Saw only |
| Accu-Cut ACS2700 | $99 | Your circular saw | Your blade | Accu-Cut track | Universal sled, Starting Block |
Still comparing brands? I put together a full ranking in I tested 15 track saws: here's the best one and the ones to avoid.
Kreg Ionic Drive Adaptive Cutting System Master Kit
Model ACSCT3000B. Cordless. Available now.
$1,106
Best for: a complete cordless sheet goods station
This is the most complete track saw setup in the new lineup. You get the cordless plunge cut track saw, the 62 inch Universal Track, and the Adaptive Cutting System Project Table. The table supports and positions your material with built in guides, stops, and measuring. Kreg designed it to replace the sawhorse and foam board setups a lot of us cobble together.
- 20V brushless plunge cut track saw with anti tip tab
- 62 inch Universal Track handles cuts up to 50 inches
- Project Table with integrated guides, stops, and measuring
- Riving knife, electronic brake, and anti kickback control
- Includes one Blue Ion 4.0 Ah battery and a charger
Kreg Ionic Drive Adaptive Cutting System Saw + Universal Track Kit
Model ACSCT2000B. Cordless. Available now.
$508
Best for: cutting sheet goods anywhere without a cord
This kit pairs the cordless brushless track saw with the 62 inch Universal Track. It's the move if you want to cut sheet goods without a cord and don't need the Project Table. The saw runs a fully shrouded, thin kerf 40 tooth blade. Kreg's product listing doesn't mention a battery, so plan on having a Kreg 20V pack ready.
- Brushless 20V motor with a 40T thin kerf blade
- Riving knife, electronic brake, anti kickback control, and anti tip tab
- 62 inch Universal Track for cuts up to 50 inches
- Zero clearance anti chip strip reduces tear out
- GripMaxx strips hold the track without clamps
Kreg Adaptive Cutting System Saw + Universal Track Kit
Model ACSCT2000. Corded. Available now.
$458
Best for: shop use near an outlet
This is the corded version of the track saw kit. It uses a 12 amp, 120V plunge cut saw with a 48 tooth blade and comes with the 62 inch Universal Track. If your saw mostly lives in the shop near an outlet, this kit makes a lot of sense. You get the same zero offset track, anti chip strip, and grip strips as the cordless kit.
- 12 amp, 120V motor with a 48T carbide tipped blade
- Riving knife, electronic brake, anti kickback control, and anti tip tab
- 62 inch Universal Track for cuts up to 50 inches
- Zero offset track design for fast setup
- GripMaxx strips and glide strips included
Kreg Adaptive Cutting System Plunge-Cut Track Saw
Model ACSSAWUNIV. Corded, saw only. Available now.
$349
Best for: anyone who already owns universal track
This is the corded saw by itself with no track. It's a good pick if you already own universal track from another brand or plan to buy a Kreg track separately. Kreg calls out a blade left design that gives right handed users a better view of the cut. It cuts 2 1/8 inches deep at 90 degrees.
- 12 amp, 120V motor with a 48T carbide tipped blade
- Blade left design for right handed visibility
- Cut depth: 2 1/8" at 90° and 1 1/2" at 45°
- Bevel range from negative 1° to 47°
- Anti tip tab fits the slot on Universal Tracks
Kreg Adaptive Cutting System Accu-Cut
Model ACS2700. Uses your circular saw. Available now.
$99
Best for: getting track style cuts from the circular saw you own
Accu-Cut turns the circular saw you already own into a guided cutting system. A universal sled mounts most 6 1/2 inch and 7 1/4 inch circular saws. This is the budget friendly way into track style cuts. Later on, you can step up to Accu-Cut XL or a full plunge saw on the same track foundation.
- Universal sled fits most 6 1/2" and 7 1/4" circular saws
- Zero clearance anti chip strips for plywood, melamine, and veneers
- GripMaxx strips hold the track in place for many cuts
- Starting Block for safe starts, cord management, and hex key storage
- Upgrade path to Accu-Cut XL or a plunge saw
Kreg Universal Track and track saw accessories
The Universal Track comes in two lengths, and both work with Kreg plunge saws, Kreg 20V circular saws, and most universal guide rail systems. The new track shares its profile with Accu-Cut, so you won't need new track if you upgrade later.
Kreg Adaptive Cutting System Universal Track 62"
Model ACSCT62. Available now.
$109
Best for: ripping full sheets of plywood
Kreg calls this the longest standard track in the industry, with a 50 inch cut capacity. It's the track included in the saw kits. You can connect tracks to rip full length sheet goods. The anti tip slot locks the Kreg plunge saw down during bevel cuts.
- Works with Kreg plunge saws and Kreg 20V circular saws
- Compatible with most universal systems, including Festool, Makita, and Milwaukee
- Anti tip design for bevel and angled cuts
- Zero clearance anti chip strip and GripMaxx grip strips
- Connects to other tracks for longer cuts
Kreg Adaptive Cutting System Universal Track 26 1/2"
Model ACSCT26. Available now.
$49
Best for: crosscuts and smaller parts
The short track has the same features as the 62 inch version in a more manageable length. It's handy for crosscuts on panels and trimming smaller parts. It also connects to a longer track when you need more capacity. If you crosscut a lot of plywood, a short track saves you from wrestling a long one.
- Same profile as the 62" track and Accu-Cut
- Compatible with most universal guide rail systems
- Anti tip, anti chip, and anti slip design
- Glide strips for steady saw travel
- Connects to other tracks
Kreg 90° and 45° Track Saw Square
Model ACS4590. Available now.
$49
Best for: fast, repeatable 90° and 45° cuts
This square locks onto the track to set up 90 and 45 degree cuts fast. It's precision machined and uses a wedge mount design. Kreg says it works with universal track and with both left and right blade saws. That means it isn't limited to Kreg saws.
- Dual angle square for 90° and 45° cuts
- Precision machined construction
- Universal track compatible
- Works with left and right blade saws
- Wedge mount for quick, accurate setup
New Kreg routers: plunge, fixed base, and trim
Kreg rolled out four routers and a standalone router motor. The two plunge routers are built to adjust from above the table in a Kreg router table, so you don't need a separate lift. Here's the quick comparison.
| Router | Price | Power | Speed (RPM) | Collets | Best fit |
|---|---|---|---|---|---|
| 20V Plunge KPTBPR225B | $299 | 2 1/4 HP, 20V brushless | 11,000 to 23,000 | 1/4" and 1/2" | Cordless plunge and table work |
| Plunge PRSPR225 | $299 | 2 1/4 HP, 12 amp | 10,000 to 25,000 | 1/4" and 1/2" | Corded plunge and table work |
| SureSpeed PRSPR325 | $399 | 3 1/4 HP, 15 amp | 10,000 to 21,000 | 1/4" and 1/2" | Heavy bits and production work |
| SureSpeed Motor PRSPR325M | $349 | 3 1/4 HP, 15 amp | 10,000 to 21,000 | 1/4" and 1/2" | Router lift upgrades |
| Trim PRSPR125 | $119 | 1 1/4 HP, 6.5 amp | 16,000 to 32,000 | 1/4" and 6 mm | Edge profiles and small work |
Kreg 20V Ionic Drive 2 1/4 HP Plunge Router Kit
Model KPTBPR225B. Cordless. Available now.
$299
Best for: cordless routing that also works in a Kreg router table
Kreg says this is the only cordless plunge router built to work natively with Kreg router tables. You can adjust bit height from above the table without a separate lift. A built in speed sensor holds RPM under load. The kit includes a Blue Ion 4.0 Ah battery and a charger.
- 2 1/4 HP brushless 20V motor, 11,000 to 23,000 RPM
- Above the table adjustment in Kreg router tables
- 2 5/8" plunge depth with three turret depth stops
- 1/4" and 1/2" collets, sub base, and guide bushing adapter
- Includes one 4.0 Ah battery and charger
Kreg 2 1/4 HP Plunge Router
Model PRSPR225. Corded. Available now.
$299
Best for: corded plunge work and Kreg router tables
This is the corded twin of the 20V plunge router. It runs a 12 amp motor with speed sensing and a wider speed range that tops out at 25,000 RPM. Like the cordless model, it adjusts from above the table in a Kreg router table. It's set up for freehand, plunge, and table routing right out of the box.
- 12 amp motor delivers 2 1/4 HP
- Variable speed from 10,000 to 25,000 RPM
- Above the table adjustment in Kreg router tables
- 2 5/8" plunge depth with three turret depth stops
- 1/4" and 1/2" collets, dust collection, and guide bushing adapter
Kreg 3 1/4 HP SureSpeed Fixed Base Router
Model PRSPR325. Corded. Available now.
$399
Best for: raised panels, big bits, and production work
This is the big dog of the lineup. The 15 amp motor is built for raised panels, large profile bits, and long production runs. A speed sensor keeps RPM steady under load for cleaner cuts. It fits the largest setting of the Kreg Router Lift PRS5000.
- 3 1/4 HP, 15 amp motor with soft start
- Speed sensor maintains RPM under load
- Variable speed from 10,000 to 21,000 RPM
- Fine adjustment ring with 1/64" graduations
- 1/4" and 1/2" collets, wrench, and guide bushing adapter
Kreg 3 1/4 HP SureSpeed Router Motor (motor only)
Model PRSPR325M. Corded. Available now.
$349
Best for: upgrading a router lift or table setup
If your router lives in a table, you may not need the base at all. This is the same SureSpeed motor without the fixed base. It drops into the Kreg Router Lift PRS5000 at its largest setting. That makes it a clean upgrade for an existing table setup.
- Same 3 1/4 HP, 15 amp motor as the full kit
- Speed sensing and soft start
- Variable speed from 10,000 to 21,000 RPM
- Drop in fit for the Kreg Router Lift PRS5000
- Includes 1/4" and 1/2" collets and wrench
Kreg 1 1/4 HP 1/4" Trim Router
Model PRSPR125. Corded. Available now.
$119
Best for: edge profiles, flush trimming, and small template work
The trim router is the one you'll grab for roundovers, flush trimming, and small template work. It has six speed settings and a soft start for better control. A quick release base makes depth changes and motor removal easy. Pair it with the new plunge base or Dock and Go table top to build out a full trim router system.
- 1 1/4 HP, 6.5 amp motor with soft start
- Six speeds from 16,000 to 32,000 RPM
- Quick release base and single wrench bit changes
- Clear base keeps the cutline visible
- 1/4" and 6 mm collets, guide bushing, wrench, and dust adapter
New Kreg router accessories
These accessories round out the new routers. Two of them turn the trim router into a more capable tool, and the others help with table setups and bits.
Kreg Trim Router Plunge Base
Model PRSTRPB. Available now.
$41.99
Best for: hinge mortises and template routing with a trim router
This base adds plunge action to Kreg trim routers. It makes template routing, hinge mortises, and inlay style cuts easier to control. A 3 step turret gives you repeatable depths. The guide bushing adapter is included.
- Smooth plunge action with fine depth adjustment
- 3 step turret for repeatable depths
- Guide bushing adapter included
- Clear dust port and chip shield
- Ergonomic plunge lock lever
Kreg Dock & Go Trim Router Table Top
Model KRTRT100. Available now.
$99
Best for: small shops that want a trim router table
Dock and Go is a compact trim router table that mounts to a bench or a wall. You can switch between freehand and table routing without tools. Kreg says the clear base plate fits all major trim router brands without drilling. It's made in the USA with globally sourced parts.
- Tool free switch from freehand to table routing
- Fits Kreg and all major trim router brands
- Bench or wall mount with multiple setup options
- Flip up bit guard and rotating dust port
- Four countersunk plate levelers
Kreg Precision Router Table Insert Plate, Predrilled for Kreg
Model PRS4040. Available now.
$62.99
Best for: mounting a Kreg plunge router in a table
This is a 3/8 inch thick phenolic insert plate for your router table. Kreg says it comes predrilled with hardware for the Kreg 2 1/4 HP plunge routers. With some modification, the hole pattern works with other routers too. Level Loc reducing rings are included.
- 9 1/4" x 11 3/4" plate size
- 3/8" thick phenolic
- Predrilled with mounting hardware included
- Alignment marks for centering other routers
- Includes Level Loc reducing rings
Kreg SureCut Router Bit Set (5 Piece)
Model PRS4325. Available now.
$34.99
Best for: starting a router bit collection
This set covers the five profiles most folks reach for first. Every bit has a 1/4 inch shank, so it fits trim routers and full size routers. The carbide tips handle hardwood, softwood, plywood, and composites. It comes in a storage case with a clear top.
- 1/4" straight bit
- 1/2" flush trim bit
- 1/8" and 3/8" roundover bits
- 1/2" 45° chamfer bit
- Works with corded and cordless routers
New Kreg joinery tools: cordless Kreg Edge and K4PRO
Kreg built its name on joinery, and this launch brings two new options. One is a cordless loose tenon joiner, and the other is a pocket hole kit with everything in the box.
Kreg Edge 20V Ionic Drive Loose Tenon Joiner Kit
Model KPTBEDGE100B. Cordless. Available now.
$499
Best for: strong loose tenon furniture joints without a cord
The Kreg Edge now runs on a battery. An oscillating carbide cutter machines mortises in seconds. Auto centering accessories and configurable edge stops mean less measuring and marking. The kit includes a Blue Ion 4.0 Ah battery and a charger.
- Brushless cordless motor with a high speed carbide cutter
- Auto centering Narrow Stock Guide and configurable edge stops
- One touch mortise width and micro adjustable fence height
- Stability Base for face mortising on panels
- Includes one 4.0 Ah battery and charger
Kreg Pocket Hole Jig K4PRO
Model K4BSTORE. Available now.
$99
Best for: beginners who want everything in one box
The K4PRO bundles the K4 jig with a full workstation base, support wings, and a drill and driver bit set. It's a solid starting point for someone new to pocket holes. The wings are the same thickness as a 2x4. That means you can extend them with standard lumber for long boards.
- Jig, base, support wings, and bits in one box
- Three hole drill guide for 1/2" to 1 1/2" material
- Hardened steel drill guides with a lifetime warranty
- Rear mounted toggle clamp
- Wings extend with standard 2x4 lumber
New Kreg 20V cordless saws
Kreg's 20V Ionic Drive platform picked up two new saws. The circular saw also ties right into the track system.
Kreg 20V Ionic Drive 7 1/4" Circular Saw
Model KPTCS725B. Cordless. Available now.
$169
Best for: 20V users who want a track ready circular saw
This brushless circular saw is built to work with Kreg Accu-Cut and the Kreg guide rails. That gives you track style cuts from a regular circular saw. It ships with a 40 tooth SureCut finishing blade. It can cut 2x material at a 45 degree bevel.
- Brushless motor with soft start and electronic brake
- Works with Accu-Cut (sold separately) and Kreg Universal Track
- 40T SureCut finishing blade included
- Cut depth: 2 7/16" at 90° and 1 7/8" at 45°
- All metal base plate and 1 1/4" vacuum port
Kreg 20V Ionic Drive Reciprocating Saw
Model KPTRC100B. Cordless. Available now.
$139
Best for: demo, remodeling, and rough cuts
This one is for demo, remodeling, and rough cuts. It runs up to 3,000 strokes per minute with a 1 1/4 inch stroke. A switch lets you pick orbital or straight cutting. Blade changes and shoe adjustments are both tool free.
- Brushless motor
- Up to 3,000 SPM with a 1 1/4" stroke
- Orbital or straight cutting switch
- Tool free blade changes and pivoting, extendable shoe
- Built in LED work light
Kreg 20V dual fast charger and sanding discs
If you're buying into several Kreg 20V tools, the new charger is worth a look. The new sanding discs fit most 5 inch random orbit sanders.
Kreg 20V Blue Ion Dual Fast Charger
Model CRGR402B. Available now.
$97.99
Best for: anyone running more than one Kreg 20V battery
This charger handles two Blue Ion batteries at once. Kreg says it charges 4.0 Ah packs twice as fast as the standard charger. It can top off two 4.0 Ah batteries in as little as 45 minutes from one LED remaining. It also wall mounts to keep your bench clear.
- Charges two batteries at the same time
- 2x faster than the standard Blue Ion charger
- Monitors temperature and charge state
- Works with all Kreg 20V Blue Ion batteries
- Wall mountable with a 6 foot cord
Kreg 5" Sanding Discs (80 to 320 Grit)
Available now in grits from 80 through 320. Link goes to the 120 grit pack.
Best for: surface prep on 5 inch random orbit sanders
Kreg's new discs use GrainEX abrasive for fast removal with less heat buildup. The 8 hole pattern works on most 5 inch sanders with 8 hole or 5 hole pads. Hook and loop backing makes swaps quick. The 120 grit pack comes with six discs and is a good all around grit for surface prep.
- GrainEX engineered abrasive grain
- 8 hole pattern fits 8 hole and 5 hole sanders
- Hook and loop backing
- Rated up to 12,000 RPM
- Available from 80 grit through 320 grit
Which new Kreg tool should you buy?
You want a full sheet goods station
Look at the Master Kit ACSCT3000B at $1,106. It's the only kit here that includes the Project Table plus a battery and charger.
You want a track saw and already have a table setup
Go with the cordless kit ACSCT2000B at $508 or the corded kit ACSCT2000 at $458. Pick cordless for mobility or corded if you work near an outlet.
You already own universal track from another brand
The saw only ACSSAWUNIV at $349 is the one to check out. Kreg says the new track matches the design used by Festool, Makita, and Milwaukee.
You're on a budget and own a circular saw
Start with Accu-Cut ACS2700 at $99. You can move up to a plunge saw later on the same track.
You want a router for a Kreg router table
Either 20V or corded 2 1/4 HP plunge router adjusts from above the table without a lift, and both are $299. For big bits and a router lift, the 3 1/4 HP SureSpeed at $399 is the heavy hitter.
You build furniture and want stronger joints
The cordless Kreg Edge handles loose tenons for $499. The K4PRO at $99 is the easy button for pocket holes.
New Kreg tools FAQ
What new Kreg tools launched on September 15, 2026?
Kreg launched new corded and cordless track saw kits, Universal Tracks in two lengths, a track saw square, and the Accu-Cut sled. The launch also includes four routers, a router motor, router accessories, the cordless Kreg Edge, and the K4PRO. Rounding it out are a 20V circular saw, a 20V reciprocating saw, a dual fast charger, and sanding discs.
How much do the new Kreg track saws cost?
At launch, the cordless Master Kit ACSCT3000B is $1,106 and the cordless Saw + Track Kit ACSCT2000B is $508. The corded Saw + Track Kit ACSCT2000 is $458, and the corded saw only ACSSAWUNIV is $349. Accu-Cut ACS2700 is $99. The 62 inch Universal Track is $109, and the 26 1/2 inch track is $49.
How much are the new Kreg routers?
At launch, both 2 1/4 HP plunge routers are $299, cordless or corded. The 3 1/4 HP SureSpeed router is $399, and the motor only version is $349. The 1 1/4 HP trim router is $119.
Is the new Kreg track compatible with Festool, Makita, and Milwaukee?
Kreg says the new Universal Track works with most universal guide rail systems, including Festool, Makita, and Milwaukee. The older Kreg track used a proprietary profile that only worked with Kreg saws.
What is the anti tip feature on the new Kreg track saws?
The new saws have an anti tip tab in the base that fits a slot on the Universal Track. It keeps the saw locked to the track when the weight shifts during bevel cuts.
Can I use my own circular saw on the Kreg Universal Track?
Yes. The Accu-Cut sled fits most 6 1/2 inch and 7 1/4 inch circular saws. The Kreg 20V 7 1/4 inch Circular Saw is also built to work with Accu-Cut.
Should I buy the corded or cordless Kreg track saw?
The corded kit uses a 12 amp, 120V motor with a 48 tooth blade. The cordless kit uses a brushless 20V motor with a 40 tooth blade. Both include the 62 inch Universal Track, a riving knife, electronic brake, anti kickback control, and an anti tip tab.
Which Kreg routers work in a Kreg router table without a lift?
Both new 2 1/4 HP plunge routers, PRSPR225 and KPTBPR225B, adjust from above the table in Kreg router tables. The 3 1/4 HP SureSpeed router is made to fit the Kreg Router Lift PRS5000.
What comes in the Kreg Ionic Drive Adaptive Cutting System Master Kit?
You get the 20V plunge cut track saw, the 62 inch Universal Track, and the Project Table. It also includes one Blue Ion 4.0 Ah battery and a charger.
Does the cordless Kreg Edge need dust collection?
Kreg says chip relief slots clear debris and reduce the need for dust extraction during shorter sessions. The kit includes a 4.0 Ah battery and charger.
Shop every new Kreg tool in one place
All of the new Kreg track saws, routers, and accessories are available now.
Shop all the new Kreg tools Affiliate link. I may earn a commission at no extra cost to you.Prices valid at the time of this post but could change at any time. Check links for current pricing.
Want tool deals like these every morning? Sign up for The Morning Cut.
The Kreg Edge is a $449 cordless loose tenon joiner that takes on the Festool Domino at one-third the price. Full specs, comparison, and launch details inside.